The reason for this will be due to the distance of the wireless router. There are many other reasons like interference from other devices or due to ceilings and walls. The following topic discusses ways to extend the Wi-Fi range and resolve the issues of poor connectivity.
Best Ways To Extend Wi-Fi Range –
1: Place the Routers At the Right Place
The design of the house actually determines the Wi-Fi signal. It is important to check the placement of the wireless router. You must always keep it open and it has to be free from obstructions. When you place the router in open-air there will be a better signal. Another advantage of doing it is it also prevents overheating. When you eliminate even a single wall, there will be better Wi-Fi performance without any impact. You need to consider other factors like ceiling or ground which may interrupt the Wi-Fi signal beams. Try to adjust the antenna in different angles to have wide coverage. Additionally, there are also tools that can enhance the network coverage.
2: Install Wi-Fi Extenders or Repeaters
When you happen to face issues even after placing the router in the right place, you will have to make use of Wi-Fi extenders or Wi-Fi repeaters. It serves great as it retains the existing wireless signal. Wi-Fi extenders can cover the corners which are out of range. Having an additional router extends the Wi-Fi coverage and requires network cabling. It works by repeating the existing wireless signal and forwarding it to the location’s dead zones. Keep in mind that the network cabling must have all the appropriate access points and setup. This method will only extend the wireless network range and not the Wi-Fi signal. It has complex maintenance and can be very expensive.
3: Upgrade Wireless Devices
The wireless device is responsible for the Wi-Fi speed. When compared to Wi-Fi 5, Wi-Fi 6 offers faster speed by up to 30%. When it is combined with MM-MIMO Technology, there will be a better tendency of improving the wireless network. For this, it is important to upgrade the router. When your wireless device is out of date, it will not provide the best speed. You will have to consider other factors including antennas and processors and confirm if the wireless device requires an upgrade.
4: Use 2.4GHz instead of 5GHz
You should know that Wi-Fi uses double frequency bands to come up with 2.4 GHz and 5 GHz signals. Many consider 5 GHz due to faster speed. However, 5 GHz signals do not have the ability to penetrate walls and ceilings when compared to 2.4 GHz signals. 2.4 GHz delivers the signal better over a greater distance. In doing so, it offers a better range even at lower speeds. For basic Wi-Fi applications, 2.4 GHz serves better than 5 GHz. However, do note that 5 GHz is less congested when there are more devices to use.
5: Configure Wireless Distribution System
When you configure a wireless distribution system (WDS), you will be able to expand wireless networks without cables. It enables you to connect two access points to have better wireless signals. WDS offers one access point for the wireless base station which can connect to the clients and the internet. Whereas the other access point will receive the signal from the wireless base station which will further send it to other clients.
6: Create Wireless Mesh Network
A wireless mesh network system has many APs spread out which act as individual nodes. These nodes communicate with each other to enhance the wireless signal. It will further extend the Wi-Fi coverage by going through multiple hops. A wireless mesh network is an up-gradation of WDS where a single AP is connected to another AP. It works by rerouting traffic signals and can cope with interference, network device failures, link failure, and power failure. You can even add more nodes and place the APs in perfect spots to prevent the cutting of the node.
7: Use Powerline Adapters
Even though the popularity of powerline adapters has reduced, it still can extend the Wi-Fi range. Traditional powerline adapters are the cheapest option for extending the Wi-Fi signal in a particular room. The technology is still being used by the Deco P9 kit. A powerline adapter works by creating a new Wi-Fi hotspot and will not boost the existing wireless network. Even though it can be expensive, it provides fast speed with versatile functions. All you have to do is to plug the adapter into the power socket and connect it to the router with an Ethernet cable. For the second adapter, you need to connect it to a power socket in the room.
Conclusion
Many people rely on better Wi-Fi network signals while doing their work. It is even very important for people who work from home. However not having the right signal will make one face a difficult time. Wi-Fi routers when combined with other devices can improve the speed so that there will be complete Wi-Fi coverage in your home. By using any of the above methods, you can easily increase the Wi-Fi range and prevent interruptions and failures. Comment * Name * Email * Website
Δ
